MJ Research PTC-200 Thermal Cycler, Weight 25lbs, Bio-Rad Laboratories, Inc. (CAT#: STEM-PEPO-0014-LGZ)

The MJ Research PTC-200 DNA Engine, now also known as the Bio-Rad PTC 200 is a reliable peltier thermal cycler boasting a polished and robust design. Thermal Valve Lid A heated lid is fitted to the PTC 200 thermal cycler to control pressure and height. Therefore, the PTC-200 system can accommodate various plastic products. This feature also enables oil-free circulation. The system's peltier effect heat pump facilitates repeated cycling using the PTC-200 thermal cycler.

The MJ Research PTC-200 thermal cycler is equipped with interchangeable sample blocks and heat pump assemblies, allowing the user to easily change formats between runs while maintaining nist-traceable accuracy. The model's single control unit is also available with different alpha modules and alpha blocks for added functionality. The user can achieve thermal control of the instrument by using the plug-in sample probe or calculation method. Block control enhances protocol compatibility, while computational sample temperature control improves speed and accuracy.

Possible MJ Research PTC-200 Supplements

Alpha modules:
dual-independently controlled blocks
microplate format
slide adapter (for up to 16 slides)

Alpha blocks:
96-well block
Dual 48-well block (to run two programs simultaneously)
384 well blocks

Condition: certified pre-owned
GENERAL
Thermal range: -5 to 105C. but no more than 30C below ambient temperature (4 to 100C for the Slide Chambers Alpha unit)
Thermal Accuracy: – or + 0.3C of programmed target at 90C- NIST-traceable
Thermal uniformity: – or + 0.4C well-to-well within 30 seconds of arrival at 90C (for most Alpha units; see specifications for individual Alpha units)
INPUT/OUTPUT
Parallel: One 25-pin 8-bit parallel interface printer port
Serial: One 9-pin RS-232 serial port for printer or remote use
IEEE: One IEEE-488 bidirectional general purpose interface bus
Display: One 20 x 4 LCD alphanumeric display
DIMENSIONS
W x L x H: 12 in. x 12 in. x 12 in.
Weight: 25lbs
MISCELLANEOUS
Ramping speed: up to 3°C/sec in models that hold 0.2ml tubes or V-well plates
Capacity: Varies with installed Alpha unit
Temperature homogeneity: 0.4°C within 30 seconds of arrival @ 60°C for all standard models.
Line Voltage: DNA Engine® cycler: 100–240 VAC rms (no adjustment needed among voltages within these ranges)
Frequency: 50–60 Hz single phase
Power: DNA Engine cycler: 850 W maximum
Fuses: Two 6.3 A, 250 V, 5 x 20 mm
Gradient Specification (96V Aplha module only)
Accuracy: +0.3°C of programmed target at end columns, 30 seconds after the timer starts for the gradient step, NIST–traceable
Column uniformity: +0.4°C, well–to–well within column, within 30 seconds of reaching target temperature
Gradient calculator accuracy: +0.4°C of actual well temperature
Lowest programmable temperature: 30°C
Highest programmable temperature: 105°C

Guaranteed to meet OEM specifications.
Equipped with RS232, IEEE-488 and parallel printer type ports.
Compatible with several Alpha modules and blocks.

Eppendorf Mastercycler EP 384 Thermal Cycler Series, Block Material Aluminum, Eppendorf (CAT#-STEM-PEPO-0023-LGZ)
Eppendorf Mastercycler Nexus Flat Thermal Cycler, 4-99°C, Eppendorf (CAT#-STEM-PEPO-0024-LGZ)
Eppendorf Mastercycler Nexus Gradient GSX1 Thermal Cycler, 4-99°C, Eppendorf (CAT#-STEM-PEPO-0025-LGZ)
Eppendorf Mastercycler Nexus Gradient Thermal Cycler, 4-99°C, Eppendorf (CAT#-STEM-PEPO-0026-LGZ)
Eppendorf Mastercycler Nexus PCR Thermal Cycler Range, Eppendorf (CAT#-STEM-PEPO-0027-LGZ)
Eppendorf Mastercycler Nexus SX1 Thermal Cycler, 4-99°C, Eppendorf (CAT#-STEM-PEPO-0028-LGZ)