Fisher Scientific 625D Incubator, Thermo Fisher Scientific (CAT#: STEM-CC-1163-LGZ)

The manufacturer of Fisher Scientific 625D Incubator is Thermo Fisher Scientific. Model is 625D. The Fisher Scientific Thermostat 625D incubator provides accurate, efficient heating for routine laboratory procedures through gravity flow convection. Internal outlet for agitators, shakers or other instruments. The vessel size is 2.5 cubic feet, the temperature range is 30°C to 75 °C, the resolution is 0.1°C, and the temperature uniformity is ±0.7 °C. Microprocessor controlled, low maintenance interior and exterior doors.

Condition: used
Volume: 2.5 cu ft
Chamber Dimensions: 18 x 18 x 13.5 in
Case Material: Enamel coated Steel
Controller Type: Microprocessor
Temperature Range (Metric): 30 to 75 °C
Material (Internal): Stainless Steel
Temperature Uniformity: ±0.7 at 37 °C
Display: LED
Insulation: 3 in. Thick Fiberglass
Material: Steel
Resolution: 0.1 °C

1. Microprocessor control.
2. The controls are conveniently located on the top of the incubator.
3. Keypad with arrow keys to increase or decrease set point temperature in 0.1 °C increments.
4. The over-temperature value is automatically set to 3 °C higher than the set value.
5. The PID controller comes with fixed parameters, and tuning is not required.
6. Circuit breaker protects the incubator from power surges; battery backup.
7. Designed to stack two units.
8. Big three-character LED display.
9. The figures show the actual temperature to the nearest 0.1 °C.
10. The display shows the current value of the set point temperature.
11. The HEAT indicator cycles on and off when the incubator heater is on.
12. When the temperature exceeds the over-temperature limit, the alarm indicator light is on; the backup controller maintains the temperature at 3°C ​​higher than the set value; the software has built-in safety backup.
13. Small, medium and large workload capacity.
14. Available in three-chamber capacity.
15. Mounting holes at 2 inches. (5 cm) spaced room walls to place shelves.
16. The small incubator can hold up to 5 racks, the medium incubator can hold up to 8 racks, and the large incubator can hold up to 11 racks.
17. Low maintenance incubator inner and outer doors.
18. Cabinets have a durable enamel coated steel look.
19. Extruded aluminum finish with acrylic powder coating.
20. The box is made of easy-to-clean stainless steel.
21. Low watt density heating element design for long life.
22. Outer door and 3" silicone gasket. Thick (7.6 cm) fiberglass insulation prevents heat loss throughout.
23. The outer door opens 180° for unimpeded entry and features two gripper latches.
24. Tempered glass inner door.
25. Steel shelves 17.37 inches. wide, 16.75 inches. Front to back (44 x 42.5cm).
26. Black synthetic rubber feet keep the incubator from sliding and allow ventilation space between the incubator and the benchtop.

Being Instruments BIC-120C Cooling Incubator, Being Instruments(CAT#-STEM-CC-2171-LGZ)
Being Instruments BIC-250C Cooling Incubator, Being Instruments(CAT#-STEM-CC-2172-LGZ)
Being Instruments BIC-60C Cooling Incubator, Being Instruments(CAT#-STEM-CC-2173-LGZ)
Being Instruments BIO-150RHP CO2 Incubator, Being Instruments(CAT#-STEM-CC-2174-LGZ)
Being Instruments BIO-190RHP CO2 Incubator, Being Instruments(CAT#-STEM-CC-2175-LGZ)
Being Instruments BIO-240RHP CO2 Incubator, Being Instruments(CAT#-STEM-CC-2176-LGZ)