Beckman L-80XP Ultracentrifuge, 1000 to 80000 rpm, Beckman Coulter (CAT#: STEM-LCPO-0101-YJL)

Beckman L-80XP Ultracentrifuge, 1000 to 80000 rpm, model L-80XP, is manufactured by Beckman Coulter. Bleeding edge technology and EASE OF USE thanks to a sophisticated on-board computer, powerful Optima eXPert software and an easy-to-use touch screen, the Optima L-XP delivers superior functionality, optimized user efficiencies, and faster turnarounds than any other ultracentrifuge Beckman has brought to market –to date!
Optima eXPert software provides unprecedented centrifugation capabilities. It assists you in developing the most efficient centrifugation methods, selecting the rotor and labware for a given application, then simulating the results before performing separations of proteins and sub-cellular particles
Optima L-XP utilizes the most advanced materials and technology to achieve the high performance needed – up to 100,000 rpm – for extending the boundaries of research. Plus, the air-cooled design of our drives delivers the most energy-efficient ultracentrifugation system ever made. And the imbalance-tolerant Optima L-XP drive safely accommodates tubes that are under- or over-filled by as much as 10%.

Condition: Certified Pre-Owned
Approximate Acceleration Time: 10 acceleration profiles–9 slow rates or maximum acceleration from 0 to set speed
Approximate Deceleration Time: 11 deceleration profiles–9 slow rates, coasting to a stop without brake, or full dynamic braking from set speed
Electrical Requirements 50 Hz, 220-240 VAC
Imbalance Tolerance: ±5 ml or 10%, whichever is greater
Maximum Heat Dissipation into Room under Steady-State Conditions: 1.0 kW (3,400 Btu/hr)
Noise Level 1 Meter in Front of Centrifuge: < 53 dBA
Set Speed: Actual rotor speed ± 10 rpm of set speed after equilibration (above 1,000 rpm)
Set Temperature: 0 to 40℃ in 1℃ increments
Set Time: To 999 hr 59 min; Hold for continuous runs
Speed Range: 1,000 to 80,000 rpm
Temperature Control: ± 0.3℃ of set temperature (after equilibration)
Ambient Temperature Range: 10 to 40℃ ambient
Clearances Required: 5.1 cm (2.0 in) sides; 15.2 cm (6.0 in) rear
Humidity Restrictions: < 95% (noncondensing)
Pollution Degree: 2
Time — Actual Display: Indicates time remaining in timed runs, time elapsed in Hold runs, or estimated time remaining in w2t runs
Vacuum: Below 5 microns (0.7 Pa)
Finish: Control panel: coated polycarbonate. Top surface: urethane paint. Other surfaces: general purpose paint.
Installation Category: Category II
Display: Shows the accumulated ?2t to two significant digits (in exponential notation)
Top Surface: Urethane paint
Keypad Material: Coated polycarbonate
Manual Operation: Indicates time remaining in timed runs, time elapsed in Hold runs, or estimated time remaining in Ω2t runs
Set w²t: Up to 9.99 × 10^14 radians squared per second
Temperature Display Actual rotor temperature in 0.1℃ increments

Easy-to-use eXPert Software
Max Speed: 80,000 rpm
Imbalance tolerant drive
GMI offers Installation & Training by our Beckman Trained Engineers
CFC FREE refrigeration
Service Maintenance Agreements available from GMI

Beckman Optima LE-80K Ultracentrifuge, 1000 - 80 000 rpm, Beckman Coulter (CAT#: STEM-LCPO-0106-YJL)
Beckman Optima XL-100 K Ultracentrifuge, 100000 rpm, Beckman Coulter (CAT#: STEM-LCPO-0107-YJL)
Beckman Optima XL-80K Ultracentrifuge, 80000 rpm, Beckman Coulter (CAT#: STEM-LCPO-0108-YJL)
Beckman Optima XL-90 Ultracentrifuge, 100000 rpm, Beckman Coulter (CAT#: STEM-LCPO-0109-YJL)
Beckman Airfuge CLS Ultracentrifuge, 110,000 rpm, Beckman Coulter (CAT#: STEM-LCPO-0110-YJL)