Fluke PM2811 In Rochester, NY, USA, Fluke power supplies (CAT#: STEM-GLEPO-1003-YJL)

Fluke PM2811 In Rochester, NY, USA, model PM2811 is manufactured by Fluke power supplies.
The Fluke 2811 Programmable Power Supply was created with automated testing in mind. The GPIB/IEEE-488 interface, output power module and output metering facilities are built in, taking up only two engineering units of rack height. The full rack-width models come equipped with rack mount ears for easy installation in a standard 19-inch rack. The front panel allows full access to all instrument functions, including voltage and current readback.
A sequence of front panel settings can be created with the AUTOSTEP mode, quickly creating an automated test pattern of user-defined voltages and currents with no need for a controller.
The optional front panel output gives the user easy access to both the power output connections and the sense lines; great for prototyping and temporary setups.

Condition: Used
Readback accuracy: (referred to the output terminals)
OUTPUT module: 30 V - 10 A - 60 W
Output Voltage range: 0 to 30 V
Output Current range: 0 to 10 A
Output Power: 60 W
Overvoltage protection range: 2 to 32 V
Accuracy: (at calibration temperature)
Output Voltage: +/- 0.04 % of setting: + 10 mV
Output Current: +/- 0.1 % of setting + 50 mA
Over Voltage Protection: +/- 0.5 % of setting: + 150 mV
Temperature: coefficient
Output Voltage: (0.016 % of setting + 2 mV)/K
Output Current: (0.05 % of setting + 2 mA)/K
Long term drift: (in an 8 hour period)
Output Voltage: 0.04 % of setting + 5 mV
Output Current: 0.05 % of setting + 10 mA
Programming Resolution: (12bit)
Output Voltage: 7.5 mV/LSB
Output Current: 2.5 mA/LSB
Over Voltage Protection: 7.5 mV/LSB
Source Effect: (for any line voltage change within rating)
Voltage: +/- (0.01 % of setting + 2 mV)
Current: +/- (0.02 % of setting + 2 mA)
Load Effect: (load change 10 % to 90 % or 90 % to 10 % full load)
Constant Voltage: +/- (0.01 % of setting + 5 mV)
Constant Current: +/- (0.02 % of setting + 5 mA)
Output Noise: (PARD)
Constant Voltage pp/rms: 15 mV/3 mV
Constant Current rms: 10 mA
Accuracy: (at calibration temperature)
Voltage: +/- (0.05 % + 25 mV)
Current: +/- (0.1 % + 30 mA)
Measuring Resolution: (12 bit)
Voltage resolution to interface: 7.5 mV
Current resolution to interface: 2.5 mA
Voltage resolution to display: 10 mV
Current resolution to display: 10 mA
Max. Current at Reverse voltage: 10 A
REMOTE SENSE: ＞ 0.25 Volt drop per lead: (at open sense connections, the output voltage will not be more than 3 V above the programmed value)
DYNAMIC OPERATION: I=1 A between 1 and 10A between 0.5 and 5A between 1 and 10A
Settling band: +/- 50 mV
dI/dt: ＜ 1 A/s
Overshoot: ＜ 150 mV
Recovery time: ＜ 1 ms
Programming response: (measured with resistive load)
Up (0 V to max. output): 100 ms @ 2 A
Up (0 V to max. output): 50 ms @ (no load)
Down (max.output to 1 V): 100 ms @ 2 A
Down (max.output to 1 V): 50 ms @ (no load)
Range: 50 ms to 60 s
Resolution: 1 ms
Default: 50 ms
Step Interval time: up to 60 s
GPIB

Load cross regulation Negligible for both voltage and current
Switching Frequency approx. 20 kHz approx.
Reprogramming delay

Fluke PM 2811 In New Smyrna Beach, FL, USA (CAT#: STEM-GLEPO-1048-YJL)
Fluke PM 2813 In New Smyrna Beach, FL, USA (CAT#: STEM-GLEPO-1049-YJL)
Fluke PM 2812 In New Smyrna Beach, FL, USA (CAT#: STEM-GLEPO-1050-YJL)
Fluke PM 2832 In New Smyrna Beach, FL, USA (CAT#: STEM-GLEPO-1051-YJL)
Fluke PM 2831 In New Smyrna Beach, FL, USA (CAT#: STEM-GLEPO-1052-YJL)
Fluke V3000 In Orlando, FL, USA (CAT#: STEM-GLEPO-1098-YJL)